65m³/min Osuszacz powietrza z podgrzewaną dmuchawą i osuszaczem o zerowej stracie powietrza do sprężarki powietrza

The desiccant air dryer is the dual tower. Lingyu is the top reliable regenerative adsorption air dryer manufacturer in China. This product is a zero air loss heated blower air dryer. So its regenerative gas consumption is 0%. For this kind of dryer, our pressure dew point can be -20℃ and -40℃.

Different from a heatless air dryer, it is an energy-saving machine. Both heating regeneration and cold purge use ambient air. It can effectively save the compressed air. So the whole operation can achieve zero gas consumption. Because it is energy efficient, it is widely used in steel, lithium batteries, chemical metallurgy, medicine, and other industries.

Our heated blower purge desiccant air dryer has many advantages. Our regenerative air dryers usually work together with famous air compressor brands. These air compressor brands are Atlas Copco, Ingersol Rand, Sullair, itp.

(1) Low Point & High Stability

It can 100% ensure -40℃ pressure dew point. Oprócz, the dew point curve is very smooth. Po pierwsze, our dryers use high-quality desiccant beads. That is a high-efficiency alumina and 4A molecular sieve. We use a Sino-foreign joint venture adsorbent brand. Oprócz, the adsorbent filling is sufficient. Take the 65m³/min heated blower air dryer as an example. The total filling volume is close to 2000 kg. This is more than other manufacturers.

Ponadto, there is an airflow splitter at the bottom of the adsorption towers. Dlatego, the compressed air can fully contact with the desiccant beads in the towers. Dry more thoroughly. Ponadto, our dryer has an intelligent control system. It can adjust the operation of the absorption air dryer in real-time. So the dew point of our desiccant air dryer for air compressor is stable.

The compressed air passes through the adsorbent layer. The moisture is separated from the wet air. After some time, adsorption reaches saturation equilibrium. Następnie, the blower blows out atmospheric air. An electric heater will heat this air. Potem, it starts heating the regeneration of the desiccant beads. So it can restore the adsorption capacity of the adsorbents. W ten sposób, the Twin Towers switch constantly and work in a cycle.

Pytanie 1: What’s The Main Material Of Your Desiccant Air Dryer For Air Compressor?

A1: The material is a Q235B pressure vessel steel plate. Oczywiście, we can also produce the stainless steel material dryer. So you can use it for the food, medyczny, and pharmaceutics industry.

Pytanie 2: What’s The Cycle Time Of Your Zero Air Loss Heated Blower Purge Desiccant Air Dryer?

A2: The cycle time of a single tower is about 4 godziny.

Pytanie 3: What’s The Maximum Pressure Of Your Adsorption Air Dryer?

A3: Our factory can also produce a high-pressure regenerative desiccant dryer. Na przykład, Lingyu can customize 40 bar 60 bar dryers. And for a normal dryer, the max pressure is 100 bar.

Pytanie 4: What is A Desiccant Dryer For An Air Compressor?

A4: It can remove the water in the compressed air deeply. And get super dew points, such as -20℃, 40℃, and 70℃. We often use it after the refrigerant air dryer. Zazwyczaj, there are dual adsorption A/B towers in the dryer.

Pytanie 5: Do I Also Need A Refrigerant Dryer Before The Heated Blower Air Dryer?

A5: We usually recommend purchasing a refrigeration dryer as well. A refrigerated dryer removes water and cools temperature down. It is better able to meet the inlet air temperature requirements of the desiccant dryer. Ponadto, it can increase the service life of the adsorbent. At the same time it ensures that the water removal effect more effectively.

Pytanie 6: What’s The Production Time Of Your Heated Blower Purge Desiccant Air Dryer?

A6: This zero air loss air desiccant dryer will take about 40~50 days.