37m³/min 공기 손실이 없는 송풍기 퍼지 재생식 공기 건조기

The regenerative air desiccant dryer has a blower. It can pump ambient air for heating regeneration. So it doesn’t consume the compressed air. Below, we will take an example. 그 다음에, compare the running costs of different regenerative desiccant dryers. 예를 들어, there is a 228m3/min oil-free centrifugal air compressor. Its power is about 1225KW. The air compressor works 365 days a year. Continuous working 24 하루에 몇 시간. The electricity price is CNY1.1/kWh. And the cost of water is CNY0.25/ton.

TSE uses the actual outlet dew point for dynamic control. It detects the saturation of the in-line tower in real-time. If it does not reach saturation, it will extend the adsorption cycle. This ensures a stable dry dew point. 게다가, it maximizes energy savings in regeneration. It can save more than 30% compared to a desiccant dryer system without TSE.

PLC intelligently controls the system. 게다가, it’s with a human-machine interface touchscreen display. Its design level is ahead of the entire air compressor dryer industry.

게다가, the desiccant dryer system has a multi-core drive mode. It can intelligently detect according to the actual conditions. 동시에, it can automatically adjust the optimal operating efficiency of the dryer. Ensure that the regeneration is truly complete. 그래서, the dew point is more stable.

게다가, it can extend the adsorption cycle automatically according to the load. 그러므로, it saves significant energy consumption. Compared to the traditional single-core control mode, energy saving can reach more than 20%.

Our regenerative air dryer uses high-quality desiccant beads. 예를 들어, 700KG activated alumina and 300KG molecular sieves are in this 37m³/min dyer. The high-pressure blower is a Taiwanese brand. It can ensure reliable and safe operation of the desiccant dryer system.

The control valves are German brand. Long service life and low failure rate. 게다가, the pneumatic components are Taiwan AirTAC brand. And the electrical components are Schneider brand.

Lingyu is the top regenerative desiccant air dryer brand in China. 게다가, our desiccant dryer system usually works with famous air compressor brands.

The air compressor discharges saturated compressed air. 그 다음에, they will pass through desiccant beads in the drying tower. 그래서, it will adsorb a large amount of water vapor. This water vapor will remain in the capillary pores of the adsorbent. The drying process will wait until the regeneration of the regeneration tower finishes. 그 다음에, start to cycle the switch.

① First is the pressure release process of the desiccant dryer system. The regeneration tower must be reduced to atmospheric pressure. Discharge pressure and start the second process.

② Second is the thermal purging process. The blower is running. It inhales the ambient air. Then the heater will heat up. 그 다음에, enter the regenerative desiccant dryer to complete the thermal purge. 마지막으로, remove and drain moisture.

③ Third is the cold purge process. The cooling process starts. 동시에, the heater stops working. The blower sucks the remaining airflow inside. These air streams flow through cooler adsorption towers. 마지막으로, back to the blower. Gradually, it reduces the temperature of the desiccant beads.

④ Fourth is the boosting process. The regeneration exhaust valve closes. 동시에, the regeneration valve remains open. Boost and reach operating pressure.

⑤ Fifth is the standby process. 이때, the regeneration tower has finished pressure boosting. The regenerative air dryer waits for the switch.

⑥ Sixth is the TSE dew point energy-saving control process. It can carry out dynamic control according to the actual dew point. So it can save energy to the greatest extent.

⑦ Finally, it is the process of transformation. So it starts a new process of desiccant dryer system.