Specifications Sheet of 20 hp Rotary Screw Air Compressor
Item Name | Đơn vị | Parameter Data of 15 kw Air Compressor |
Nominal air flow/ rated discharge air pressure | (m3/min)/ MPa | 2.2tôi3/min@0.8MPa, 2.0tôi3/min@1.0MPa, 1.7tôi3/min@1.2MPa (≈80 cfm @7bar) |
Ambient Tempe. | ℃ | -5~+45 |
Cooling type | Air-cooled air compressor | |
Discharge temp. | ℃ | ≤Ambient Temp.+15 |
Oil volume of 20 hp screw compressor | L/kg | 10L |
Drive type of industrial screw compressor | Direct | |
Adjustment way of air flow | ON/OFF | |
Oil content in exhaust air | trang/phút | 3 |
Noise of 15kw screw compressor | dB(MỘT) | 68±2 |
Air compressor lubricating oil brand | Shell brand, model S46 | |
Safety valve setting pressure | MPa | Working pressure x1.2 |
Screw compressor motor power | kW | 15 |
Motor rotating speed | rpm | 3000 |
Starting mode | PM VFD | |
Voltage/frequency | V/Hz | 380/50 (other voltages also available) |
Protection class of compressor motor | IP23/IP54 available | |
Dimensions of 20hp screw compressor | mm | 1080x750x1000 |
Net weight of 15kw compressor | Kilôgam | 254 |
Outlet size | TRONG | Rp3/4 |
loại lưu ý: we also customize 20 hp screw air compressor with other voltages, such as 220V/240V/415V/440V/460V and 60HZ.
Advantages of Our 15 kw Screw Air Compressor
(1) Energy-saving
Compared with the power frequency air compressor, it can generally save energy by 10%~35%. Tất nhiên rồi, how much energy is saved depends on two aspects. Đó là, the working conditions and the setting of the parameters of the inverter. The biggest factor is the working condition of the industrial air compressor. When the customer’s actual air consumption fluctuates greatly, then the energy-saving effect will be better. The direct data is the ratio of the no-load time to the total working time.
(2) Low Maintenance Cost
The soft start of the air compressor reduces electrical shock to the motor components. The starting current is small. Vì thế, it extends the lifetime of the motor. Đồng thời, it also reduces the mechanical impact on the equipment. Correspondingly, it improves the service life of motor bearings, main engine bearings, and gearboxes.
Ngoài ra, the energy-saving controller keeps the air compressor in a loading state most time. It reduces the action number of both solenoid valves and pneumatic components. Vì thế, the failure rate without these accessories becomes lower. Hơn thế nữa, the reverse filtration time of the inlet filter is greatly reduced. It extends the filter lifetime of a 20 hp screw compressor.
(3) Low Noise
When the exhaust air volume decreases, the speed of the compressor motor slows down. So the noise is much less than when running at full speed. The unloading run time becomes less, venting noise is also reduced.
(4) Wider Exhaust Air Volume Adjustment Range
Permanent magnet motors can maintain extremely high motor efficiency at low speeds. Đồng thời, it allows the max speed to exceed the upper limit of the rated speed. Vì thế, the adjustment range of exhaust volume can reach 15%-115% of the rated flow. So the application of a 15 kw air compressor will be more flexible.
(5) Higher Transmission Efficiency
Belt drive efficiency is typically 0.94 – 0.96. Our 7.5 hp 5.5 kw screw compressor is belt drive type. Ngoài ra, the direct drive efficiency is above 0.99. This 20 hp rotary screw air compressor is a direct drive type. The permanent magnet motor does not have any mechanical friction loss or transmission loss. The transmission efficiency is 1.
How to Maintain Our Industrial Rotary Screw Air Compressor?
Regular maintenance can effectively reduce or avoid failures. So it can reduce the maintenance cost of 15 kw air compressor. Đồng thời, it can avoid affecting the product quality. If the oil content in the exhaust air is unqualified, it will cause products to be scrapped. Ngoài ra, it is also good for energy saving and consumption reduction. Bad operation of industrial air compressors often increases friction and energy consumption. Sau cùng, it will affect the energy-saving effect of the screw air compressor.
(1) Air Compressor Air Filter Maintenance
It can filter out dust and other dirt in the air. The best time for maintenance is once a week. The specific method is as follows: Trước hết, take out the air filter of 20 hp screw compressor. Then use a certain amount of compressed air to blow the inside out. Clean up the dirt on the surface of the part. Cuối cùng, wipe it clean with a clean cloth.
(2) Industrial Air Compressor Oil Filter Maintenance
For the new 15 kw air compressor, replace the oil filter after use for more than 500 giờ. After that, we can change it every 2000 hours or so.
(3) Compressed Air Oil Separator Maintenance
The best replacement time is around 3,000 giờ. But in the case of relatively bad conditions, it is necessary to shorten the replacement time. Đồng thời, we need to take the oil separator out in due course for cleaning.
(4) Screw Compressor Lubrication Oil Maintenance
The quality of lubricating oil directly determines the performance of the oil-injected screw compressor. Good oil can make the machine run normally and efficiently. And for a new industrial compressor, it is best to replace the oil after 500 hours of use. After that, we can replace it after every 2,000 giờ.
(5) 20 HP Rotary Screw Air Compressor Air Cooler Maintenance
The cooler can cool down and dissipate heat. After long use, các 15 kw air compressor will become hot. If there is a problem with the cooler, the screw compressor will collapse. Ngoài ra, the air cooler has a special structure. This makes it prone to dust accumulation. So it is necessary to regularly clean the dust.
câu hỏi thường gặp
Q1: How many CFM is a 20 hp screw air compressor?
A1: Different pressures, different air flows. If the pressure is 8 quán ba, the airflow of the 15 kw air compressor is 2.2m³/min. Đó là, the airflow is 77 cfm. And if the pressure is 7 quán ba, the airflow is 2.5m³/min (≈80 cfm).
quý 2: What’s the average lifespan of a rotary screw air compressor?
A2: Under normal circumstances, it is no problem to use it for 10 năm. Tất nhiên rồi, we have to do a good job of daily maintenance.
Q3: What’s the delivery time of your 20 hp rotary screw air compressor?
A3: Different voltages and configurations, different delivery times. If 380V/50HZ 15 kw air compressor, our delivery time is 15~20 days. But if special custom screw compressor, the delivery time is about 35~40 days. Ví dụ, many customers need 220V/415V/440V/460V and 60HZ air compressors. The lead time is longer than 380V/50HZ screw compressor.