Technical Sheet of HOC Type Absorption Air Dryer
| Equipment name | zero air consumption heat of compression desiccant dryer |
| 進氣量 | Std.210.0 Nm3 / 分鐘 | 12600 立方米 / 小時 |
| Dryer working principle | TSA變溫吸附 + split flow cycle regeneration |
| 工作期限 (單塔) | 約240分鐘 | 最長300分鐘 |
| 再生空氣損失 | 0% |
| 進氣壓力 | 標準 7 巴 |最小. 6 最大 10 bar |
| 滿載壓力損失 | ≤7% of inlet pressure |
| 進氣油要求 | Oil-free compressed air |
| 進氣溫度 | Std.140℃ | Min.120℃, Max.180℃ |
| 出口壓力露點 | ≤-40℃ |
| Absorption air dryer power | 50.2 千瓦 |
| 鼓風機功率 | 7.5千瓦 |
| 電加熱器功率 | 50千瓦 (heating by 40% flow) |
| 加熱溫度 | 倫敦大學學院：150℃，拼箱：120℃ |
| 冷卻水流量 | ≤116T/Hr |
| 冷卻水壓力 | Std.3 bar Min 2 最大酒吧:6 酒吧 |
| 冷卻水溫度 | temperature rise | Std.20℃ Min 2℃ Max:27℃ | 5℃ |
| 吸收式乾燥機重量 | 12000 公斤 |
| HOC air dryer size | 2950 H×5000 L×3200W |
Why Choose Our Zero Air Loss HOC Type Absorption Air Dryer
(1) Energy Efficient
Among all the adsorption air dryers, this one is the most energy-efficient. Compared to a normal HOC dryer, it adds an auxiliary high-efficiency cooler. 所以, it achieves complete zero air consumption. Compared with a heatless air dryer, it can save energy by about 80%.
現在, let’s take an example. And compare the energy consumption of different desiccant dryers. 例如, a 175m³/min oilless centrifugal air compressor exists. And the power is 925KW. Assume that the centrifugal air compressor works 365 一年中的天數. 同時, it runs continuously each day. 此外, the electricity fee is CNY1.05/kWh. The water fee is CNY0.22/ton.
Specific energy consumption of each absorption dryer:
| 不. | Air Compressor Air Dryer | Calculation of energy consumption for each absorption air dryer |
Annual operation fees | Compared to heatless dryer, how much energy it can save? |
| 1 | Heatless desiccant air dryer | The ratio of regeneration air consumption is about 15%. (925功率×15%)×24h×365d×CNY1.05 =CNY1276222/year |
CNY1276222 | 能耗高 |
| 2 | Heat regenerative adsorption dryer | Single tower cycle is 4h. 此外, regeneration air volume is 8%. 和 heater power 70KW. Heating time 1.5h. Cold purge time 2.0h. (925KW×8%×3.5h+70KW×1.5h×75%)× 6 times×365d×CNY1.05=CNY776656/year. |
CNY776656 | 39.10% |
| 3 | 零空氣損失鼓風機吹掃 除濕乾燥系統 |
Absorption cycle is 4h. Zero gas consumption. 加熱時間 1.5 H. Heating power 110 千瓦. 此外, cold purge time 2.0 H. 鼓風機功率 18 千瓦. And blower start time is 3.5 H. (110KW×1.5h×75%+18KW×3.5h)×6次×365d× CNY1.05=CNY429431/year |
CNY429431 | 66.30% |
| 4 | Micro air consumption HOC dryer | The adsorption cycle is 4h. 和 5% of cold purge air consumption. Cold purge time 1.5h. Cooling water consumption: 90t/h. 能量消耗: (925KW × 5% × 1.5h) × 6 times × 365d × CNY1.05= CNY159527/year; Water consumption: 90t/h×24h×365 days× CNY0.22 =CNY173448 /year; So the total energy consumption of this absorption dryer=CNY159527/year + CNY173448 /year=CNY332975/year |
CNY332975 | 73.90% |
| 5 | Zero air loss HOC dryer | The adsorption period of absorption air dryer is 4h. Cooling water consumption: 135t/h. Water consumption: 135t/h×24h×365 days×CNY0.22 =CNY260172 /year |
CNY260172 | 79.60% |
(2) 穩定的露點
Our HOC dryer is with an EBZ200-2 multi-core drive intelligent control system. 除了, it adopts PLC for intelligent control. It automatically adjusts for optimum operating efficiency. And it ensures thorough regeneration. 所以, the dew point is much more stable.
此外, there are air distribution devices at the bottom of the dryer. This increases the contact time with the adsorbent. Make sure the dew point temperature meets the requirements. Our zero air loss absorption dryer can reach -20 and -40℃.
(3) Use High-performance Metal Seated Pneumatic Butterfly Valve
The temperature conditions of the HOC dryer vary greatly. Ordinary valve gaskets are prone to aging and deformation. 所以, it will cause the valve not to seal tightly. 最後, it will affect the performance of the absorption air dryer. 尤其, it affects the dew point of the desiccant dryer.
To eliminate these problems, we use high-performance metal seat valves. They can withstand high temperatures. 除了, it is a German original brand.
(4) High Quality And Sufficient Desiccant Beads
首先, our HOC dryer has ample desiccant beads. 25~28kg adsorbent per cubic air. 所以, it can maintain a high drying effect.
第二, choose a well-known brand of adsorption desiccant. 粒徑3~5mm. Good water resistance. 而且, we use the best filling method. It can prevent desiccant from sinking. So it has a longer service life.
Specific Workflow of “heat of compression” Dryer
(1) Adsorption Drying Process of HOC dryer
This process is the same as other absorption air dryers. Adsorbents hold water vapor. This process continues until another tower finishes the regeneration process.
(2) Regeneration Process of Desiccant Air Dryer
The regeneration process consists of 3 腳步: twin towers co-current → {hot purge → thermal delay → cold purge} → twin towers co-current
① Two Towers Co-current
有時, the absorption air dryer shuts down abnormally. This can avoid affecting the outlet temperature.
② Thermal Purge Process
Take tower A adsorption as an example. The high-temperature air enters the B tower from the V2 valve. 然後, it starts thermal purging from top to bottom. 之後, the main cooler will cool them to the adsorption temperature. 最後, enter Tower A.
③ Cold Purge Process
The thermal purge process ends. 此時, desiccant beads are in a dry state. 所以, it must cool to be ready for the next adsorption. 然後, the cold purge process starts.
The high-temperature air is cooled to about 40℃ by the main cooler. 然後, it performs a cold purge to tower B through the V4 valve. 下一個, flow through the auxiliary cooler to cool to the adsorption temperature. 最後, enter the A tower from V8 and V5.
常見問題解答
The use of compression heat dryers is conditional.
It is generally only suitable for centrifuges and oil-free screws. Compressed air inlet temperature should be above 110°C. 除了, the dew point requirements are not strict. 例如, -20℃, or -40℃. 此時, the energy saving of the HOC absorption dryer is beyond doubt. It can achieve zero air consumption.
But sometimes customer requirements are very strict. 例如, they require a dew point lower than -40℃. And the inlet temperature is not always guaranteed to reach 110°C. 然後, the energy saving of the HOC absorption air dryer will be greatly reduced. 此時, we should choose a micro air consumption dryer. It’s better than a zero air loss HOC adsorption dryer.
是的. For the HOC absorption air dryer, we must confirm the inlet air temperature. It usually cannot be lower than 110°C. 有時, the intake air temperature is lower than 110°C. 除了, users have strict requirements on dew point. 然後, the desiccant dryer must add auxiliary heating.
For a single tower, it’s about 240 分鐘. Namely, 4 小時. Many people believe that long-term operation is good. I think it shows the energy saving and performance of the adsorption dryer. But this does not apply to zero air-loss desiccant air dryers.
For other dryers, the regeneration process releases moisture-laden air into the atmosphere. 然而, the HOC absorption dryer is different. It will carry some moisture from the previous cycle to the next one. The cycle adsorption capacity of an HOC dryer is much larger than that of other dryers. 所以, if we need the same dew point, we can increase the filling amount of the adsorbent. 然而, shortening the adsorption cycle is the best way. 所以, a short cycle time is good for zero air loss absorption air dryer.
