Specifications Sheet of Our Heated Desiccant Air Dryer
Compressed Air Dryer Parameter | ข้อมูล |
Adsorption Dryer Inlet Air Capacity | Std.6.5 Nm3 / นาที | 390 Nm3 / ชม | 227 ซีเอฟเอ็ม |
Working Principle | PSA pressure swing adsorption+TSA temperature swing adsorption |
Work Cycle | 90~240 นาที (ปรับได้) |
Average Consumption of Regenerative Air | มาตรฐาน 6% | นาที. 3.5% สูงสุด. 8% |
ความดันอากาศขาเข้า | แถบ Std.7 | นาที. 6 บาร์| สูงสุด 10 บาร์ |
Pressure Loss at Full Load | 0.2 บาร์ |
Inlet air oil content requirements | Oil-less air or ≤0.1ppm(mg/m3) |
อุณหภูมิอากาศเข้า | 10~30℃ | ต่ำสุด 2 ℃ สูงสุด 40 ℃ |
Intake Air Dew Point | ≤15℃ |
Dew Point of Outlet Compressed Air (Nominal) | ≤-40℃หรือต่ำกว่า Sure100% |
Working Environment Temp. | ต่ำสุด 2 ℃ สูงสุด 45 ℃ |
Air Inlet / ขนาดพอร์ตทางออก | R1-1/2″ male thread/ DN40 |
Power of Heated Desiccant Air Dryer | 3.6กิโลวัตต์ |
Air Compressor Dryer Weight | 443 กิโลกรัม |
Overall dimensions (ยาว*กว้าง*สูง) | 1090×680×1877 mm |
Structure Type | Twin tower integral vertical |
Noise of Desiccant Air Dryer System | Noise less than 70 dB at 1 m from the equipment |
Surface Coating of Twin Tower Air Dryer | Anti-rust primer + double coat corrugated high gloss top coat |
Adsorption Towers Material | Pressure vessel steel plate |
Adsorbent Type | Activated alumina and molecular sieves (3~5mm size) |
Power of Electric Heater | 3.5กิโลวัตต์ |
Power Consumption During Heating | <25% of total heating power |
Heating Temperature | ยูซีแอล: 180องศาเซลเซียส, ลค: 170องศาเซลเซียส | Intelligent Thermostat Control |
Technical Advantages of Our Heated Regenerative Desiccant Air Dryer
(1) More Energy Efficient
Micro heat desiccant air dryer has an electric heater. It can take advantage of some ambient air. ดังนั้น, the regeneration air consumption is much lower in a heatless dryer. ด้านล่าง, we will compare the operating costs of the two dryers.
Item | เครื่องหมาย | ข้อมูล | หน่วย | หมายเหตุ |
Air Flow | ถาม | 6.5 | ลบ.ม./นาที | —— |
Heater Power | ป1 | 0 | กิโลวัตต์ | there is no heater |
พลังโบลเวอร์ | ป2 | 0 | กิโลวัตต์ | ไม่มีเครื่องเป่าลม |
Average Air Consumption | ถาม | 15 | % | —— |
ปริมาณการใช้น้ำ | โวลต์ | 0 | ไทย | ไม่ต้องการน้ำหล่อเย็น |
ค่าไฟฟ้า | ย1 | 1 | หยวนจีน | ไฟฟ้าอุตสาหกรรม |
Water Fee | ย2 | 0.2 | หยวนจีน | น้ำรีไซเคิลทางอุตสาหกรรม |
ค่าไฟฟ้าต่อ ลบ.ม. อากาศ | เค | 5.8 | กิโลวัตต์ | —— |
เวลาการฟื้นฟูหอคอยเดี่ยว | ที1 | 5 | ชม. | —— |
เวลาทำความร้อน | ที2 | 0 | ชม. | not need heating |
Absorption Dryer Cold Purge Time | ที3 | 5 | ชม. | —— |
เวลาทำงานของโบลเวอร์ | ที4 | 0 | ชม. | ไม่จำเป็นต้องเป่า |
Working Time of Desiccant Air Dryer System | ต | 8000 | ชม. | —— |
Air Consumption Converted into Electrical Energy | 45240 | หยวนจีน | ค่า=(คิว*คิว*เค*ท) | |
ไฟฟ้าที่สร้างจากเครื่องทำความร้อน | 0 | หยวนจีน | ค่า=(P1*t2*0.7+P2*t4)*ที/4 | |
Water Fee | 0 | หยวนจีน | ค่า=(ว*y2*ท) | |
Total Running Charges of Heatless Dryer | 45240 | หยวนจีน | —— |
Running Charges of Micro Heated Desiccant Air Dryer
Item | เครื่องหมาย | ข้อมูล | หน่วย | หมายเหตุ |
Air Flow | ถาม | 6.5 | ลบ.ม./นาที | —— |
พลังงานเครื่องทำความร้อนไฟฟ้า | ป1 | 3.5 | กิโลวัตต์ | —— |
พลังโบลเวอร์ | ป2 | 0 | กิโลวัตต์ | no blower |
Average Air Consumption | ถาม | 6 | % | —— |
ปริมาณการใช้น้ำ | โวลต์ | 0 | ไทย | no cooling water |
ค่าไฟฟ้า | ย1 | 1 | หยวนจีน | ไฟฟ้าอุตสาหกรรม |
Water Fee | ย2 | 0.2 | หยวนจีน | recycling water |
ค่าไฟฟ้าต่อ ลบ.ม. อากาศ | เค | 5.8 | กิโลวัตต์ | —— |
One Tower Regeneration Time | ที1 | 4 | ชม. | —— |
เวลาทำความร้อน | ที2 | 1.5 | ชม. | —— |
Adsorption Dryer Cold Purge Time | ที3 | 2 | ชม. | —— |
Blower Running Time | ที4 | 0 | ชม. | ไม่จำเป็นต้องเป่า |
Operation Time of Desiccant Air Dryer System | ต | 8000 | ชม. | —— |
Air Consumption Converted into Electrical Energy | 18096 | หยวนจีน | ค่า=(คิว*คิว*เค*ท) | |
ไฟฟ้าที่สร้างจากเครื่องทำความร้อน | 7350 | หยวนจีน | ค่า=(P1*t2*0.7)*ที/4 | |
Total Water Fee | 0 | หยวนจีน | ค่า=(ว*y2*ท) | |
Total Running Charges of Heated Desiccant Air Dryer | 25446 | หยวนจีน | —— |
เพื่อสรุป, the micro heat dryer is more energy-efficient than the heatless dryer. Assume that the flow rate of the dryer is 6.5m³/min. The former saves CNY19794/year than the latter.
(2) Reliable And Stable Dew Point Guarantee
Our desiccant air dryer system uses a long airflow channel design. Not only does it reduce noise, but it also has an extremely low dew point. นอกจากนี้, our heated desiccant air dryer is filled with enough adsorbents. So its drying effect is perfect. นอกจากนี้, this heated desiccant air dryer has an electric heater. There is a thermostatic controller. It can keep the regeneration air temperature constant. ดังนั้น, prevent the sorbent from overheating.
Another structure advantage is airflow distribution. There are diffuser devices at the bottom of the adsorption towers. This allows the adsorbent to absorb the water fully. Airflow is slow. It also reduces the pressure loss. ในเวลาเดียวกัน, it can reduce the wear on the desiccant beads. ดังนั้น, our adsorption air dryer can reach a low dew point. นอกจาก, the dew point curve can remain smooth.
(3) Quality Dryer Spare Parts
We use the AirTAC brand two-position five-way solenoid valves. ทางนี้, control the switching of the pneumatic valves. Electrical components are also well-known brands. To ensure the reliable operation of the dryer.
How Does Micro Heated Regenerative Desiccant Air Dryer Work
It uses the PSA + TSA working principle. At high pressure and low temperature, the adsorbent has adsorption properties. In turn, it has desorption properties at low pressure and high temperature. This increases the adsorption capacity of the desiccant beads per unit weight. ดังนั้น, it realizes deep drying of compressed air. Micro heat desiccant air dryer system includes the working processes:
(1) Adsorption And Drying Process
Compressed air passes the drying tower (e.g., tower A). Aluminum oxide and molecular sieves absorb large amounts of water vapor. This adsorption process continues until Tower B is completed regeneration.
(2) Regeneration / Desorption Process
The dryer desorption process includes six steps. ประการแรก, the regeneration tower (e.g., tower B) reduces pressure to atmospheric pressure. ประการที่สอง, it starts the hot purge process. It will consume about 3~8% compressed air. And an electric heater will heat the air. So it can remove the water in the regeneration tower. ประการที่สาม, the cold purge process begins. It also uses 3~8% compressed air as regeneration air. They can cool down the temperature of desiccant beads.
The A/B tower constantly switches workflows. ในที่สุด, the compressed air enables deep drying. Above is the working principle of a heated desiccant air dryer system.