300ลบ.ม./นาที เครื่องทำลมแห้งอุตสาหกรรมอัดเย็นแบบระบายความร้อนด้วยน้ำ

• The inlet and outlet pressure difference of the dryer is about 0.01MPa. Below 0.015MPa. So we can set lower discharge pressure for the air compressor. Then it will consume less energy. We are a refrigerator air dryer manufacturer.
• It uses a pure counter-flow heat exchange system. The temperature difference between the air inlet and outlet is 10 องศาเซลเซียส. The system can recover 40% more cooling capacity than traditional refrigerant air dryers. This is the reason for the energy saving. Under the same working conditions, it can save energy by over 30%. Achieve “low dew point” and “low energy consumption”.
• This industrial air compressor dryer uses Hanbell screw refrigerant compressor. It has an energy regulation function. This is equivalent to a vsd refrigerant dryer. It can automatically adjust according to air consumption. So it is good for energy saving.

This water-cooled refrigerant dryer has a lower dew point. The dew point of the traditional dryer is 2~10℃. อย่างไรก็ตาม, this one can reach 2~8℃. นอกจาก, it’s 100% guaranteed. It uses a plate heat exchange system. The heat exchange efficiency is higher. So it can guarantee a stable low dew point.

• ประการแรก, use Hanbell’s refrigerant compressor. It has super cooling and low noise. นอกจาก, it’s with automatic energy regulation. So power saving and durable.
• ประการที่สอง, refrigeration accessories are all world-famous brands. ตัวอย่างเช่น, the expansion valve adopts the Danfoss brand. The hot gas bypass valve is from Sporland, USA. They ensure the stable operation of industrial air compressor dryer systems.

• Remote communication: MODBUS realizes remote collection, การตรวจสอบ, start, and stop of the dryer;
• Local/remote switch: the passive dry contact signal. So it can realize the remote start and stop of the dryer;
• Interlocking control: passive dry contact signal. It enables the linkage control of the water-cooled dryer and air compressor;

It has the same application as other industrial air compressor dryers. นอกจาก, this air dryer can be suitable for higher requirements. Because it uses the aluminum alloy heat exchanger system. นอกจากนี้, the inner pipings are also 304 สแตนเลส. They don’t rust. ดังนั้น, it can avoid secondary pollution. And the refrigerant is eco-friendly, R407C or R410A. So the refrigerant air dryer can be used for food and medical industries. It can also apply to the Lithium battery industry.

The screw compressor exhausts compressed air. At first, they are hot and humid. ประการแรก, they enter the water-cooled precooler. Condenses and cools down. หลังจากนั้น, come into the heat exchanger. They will exchange heat with dry compressed air. It can reduce the saturation of their temperature. So remove some moisture.

แล้ว, they enter the evaporator of the refrigerator dryer. Cool the compressed air to the pressure dew point. That is 2~8℃. Moisture and some impurities are condensed here. Immediately after, they are separated by a separator. ในที่สุด, it discharged out of the industrial air compressor dryer.

The low temp liquid refrigerant flows into the evaporator. They will absorb a lot of heat. Then they will be evaporated into a vapor state. ในที่สุด, they will be sucked into the compressor.

The compressor compresses them into high-temperature and high-pressure gas. The hot gas bypass valve has an automatic adjustment function. Some gas will go into the evaporator.

แน่นอน, most gas goes to the water-cooled condenser. Condenses and cools liquid refrigerant. หลังจากนั้น, go through the filter drier. Then enter the thermal expansion valve. ที่นี่, the pressure is reduced by throttling. So they will become low-pressure liquid. ในที่สุด, they enter the evaporator again. Then cycle over and over again.